Knowledge Base

Free to use workshop manual for your 2015+ Mk4 'ND' Mazda MX-5
Home

 

< Previous   Next >

DTC INSPECTION [BLIND SPOT MONITORING (BSM) CONTROL MODULE]

CMDTC Self Test

1. Connect the M-MDS to the DLC-2.
2. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.
a. Select “Self Test”.
b. Select “All CMDTCs”.
3. Verify the DTC according to the directions on the screen.
4. After completion of repairs, clear all DTCs stored in the blind spot monitoring (BSM) control module (LH). (See CLEARING DTC [BLIND SPOT MONITORING (BSM) CONTROL MODULE].)

ODDTC Self Test

1. Connect the M-MDS to the DLC-2.
2. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.
a. Select “Self Test”.
b. Select “Modules”.
c. Select “BSM”.
3. Verify the DTC according to the directions on the screen.
4. After completion of repairs, clear all DTCs stored in the blind spot monitoring (BSM) control module (LH). (See CLEARING DTC [BLIND SPOT MONITORING (BSM) CONTROL MODULE].)

Snapshot Data

NOTE:

  • The blind spot monitoring (BSM) control module (LH) stores the following two types of snapshot data (vehicle information) when a DTC is detected and displays them in the M-MDS.

    • Vehicle information detected by blind spot monitoring (BSM) control module (LH)

    • Vehicle information detected by instrument cluster and received by blind spot monitoring (BSM) control module (LH) via CAN communication

  • The data for all DTCs currently detected is stored.

—: Not applicable

Snapshot data item

Unit

Data contents

Data read/use method

Corresponding data monitor items

AAT

°C

°F

Ambient temperature

—

—

APP_STATUS

Accelerator Pedal Off/Under20%/Over20%/FAIL

Accelerator pedal position status

—

—

CFG_STATUS

Config Complete/Not Configured/Config Error

Instrument cluster configuration status

—

—

ECT_STATUS

Under 0 degrees C/0 - Under 80 degrees C/Over 80 degrees C/FAIL

Engine coolant temperature status

—

—

IC_VPWR

V

Instrument cluster power supply voltage

  • The blind spot monitoring (BSM) control module (LH) constantly receives the power supply voltage value of the instrument cluster sent via CAN communication from the instrument cluster.

  • If a DTC is detected, the blind spot monitoring (BSM) control module (LH) records the power supply voltage of the instrument cluster when the DTC was detected, and it is displayed in the M-MDS.

VPWR*1

IG-ON_TIMER

hh:mm:ss*2

Elapsed time since ignition was switched ON (engine off or on)

NOTE:

  • The instrument cluster records the elapsed time since the ignition was switched ON (engine off or on).

  • The blind spot monitoring (BSM) control module (LH) constantly receives the elapsed time since the ignition was switched ON (engine off or on) sent via CAN communication from the instrument cluster.

  • If a DTC is detected, the blind spot monitoring (BSM) control module (LH) records the elapsed time since the ignition was switched ON (engine off or on) when the DTC was detected, and it is displayed in the M-MDS.

—

PWR_MODE_KEY

Key Out/Key Recently Out (Position 0)/Accessory (Position 1)/Post Ignition (Position 2)/Ignition On (Position 2)/Running (Position 2)/Running - Starting

  • Key Out: Ignition switched off

  • Key Recently Out (Position 0): Elapsed time within 3 s since ignition was switched off

  • Accessory (Position 1): Ignition is switched to ACC

  • Post Ignition (Position 2): Elapsed time within 3 s since ignition was switched ON (engine off or on)

  • Ignition On (Position 2): Ignition switched ON (engine off)

  • Running (Position 2): Ignition switched ON (engine on)

  • Running - Starting: Cranking condition

  • The blind spot monitoring (BSM) control module (LH) constantly receives the ignition switch status sent via CAN communication from the instrument cluster.

  • If a DTC is detected, the blind spot monitoring (BSM) control module (LH) records the ignition switch status when the DTC was detected, and it is displayed in the M-MDS.

—

RPM_STATUS

Engine Stop/Under1500rpm/Over1500rpm/FAIL

Engine speed status

  • The blind spot monitoring (BSM) control module (LH) constantly receives the engine speed sent via CAN communication from the instrument cluster.

  • If a DTC is detected, the blind spot monitoring (BSM) control module (LH) records the engine speed when the DTC was detected, and it is displayed in the M-MDS.

TACHOMTR*1

SHIFT_STATUS

P/N/D/R/FAIL

Selector lever position status

  • The blind spot monitoring (BSM) control module (LH) constantly receives the selector lever position sent via CAN communication from the instrument cluster.

  • If a DTC is detected, the blind spot monitoring (BSM) control module (LH) records the selector lever position when the DTC was detected, and it is displayed in the M-MDS.

—

TOTAL_DIST

km

Miles

Accumulated total traveled distance from completion of vehicle until blind spot monitoring (BSM) control module (LH) detects DTC (Odometer value in instrument cluster)

The total traveled distance from which the blind spot monitoring (BSM) control module (LH) detects DTCs to the present can be calculated by performing the following procedure.

  • Verify the odometer value in the instrument cluster.

  • Verify the snapshot data item TOTAL_DIST.

  • Subtract 2 from 1.

—

TOTAL_TIME

hh:mm:ss*2

Accumulated total elapsed time since vehicle completion until blind spot monitoring (BSM) control module (LH) detects a DTC

NOTE:

  • When the ROOM fuse is removed, and the ignition is switched off, the time is not included in the elapsed time.

The elapsed time from which the blind spot monitoring (BSM) control module (LH) detects DTCs to the present can be calculated by performing the following procedure.

  • Verify the instrument cluster PID item TOTAL_TIME.

  • Verify the snapshot data item TOTAL_TIME.

  • Subtract 2 from 1.

TOTAL_TIME*1

VPWR

V

Blind spot monitoring control module (LH) power supply voltage

—

VPWR_L

VSPD_STATUS

Stop/0-10km/h/Over10km/h/FAIL

Vehicle speed status

  • The blind spot monitoring control module (LH) constantly receives the vehicle speed sent via CAN communication from the instrument cluster.

  • If a DTC is detected, the blind spot monitoring control module (LH) records the vehicle speed when the DTC was detected, and it is displayed in the M-MDS.

SPEEDOMTR*1
*1
Instrument cluster PID (See PID/DATA MONITOR TABLE [INSTRUMENT CLUSTER].)
*2
The seconds may be indicated after the decimal point.
< Previous   Next >
 

Free to use workshop manual for your 2015+ Mk4 'ND' Mazda MX-5

COPYRIGHT NOTICE:
This fan site is not affiliated with Mazda, and is intended for personal, or commercial use only. The content of our web pages is for general information purposes only and is presented “as is”. We give no assurance or warranty regarding the accuracy of the contents. Readers should do their due diligence and seek the advice of an appropriately certified automotive technician before attempting any steps on this site. Original content provided by Mazda North America. The content of the manual is copyright under DMCA to: full.metal.resistor@gmail.com
LIMITATION OF LIABILITY:
We accept no responsibility for errors, inaccuracies, or omissions found on these pages. Additionally, we hereby exclude liability for any demands, claims, damages or losses of any kind with regard to any content or information provided on our web-site, including but not limited to incidental or consequential damages, direct or indirect loss, compensatory damages, loss of profits, or otherwise. By using this manual you assume full liablity for any procedures carried out on your vehicle, and are responsible for the vehicle remaining road legal and safe.