Manual pages - MX5 Manual | Mazda MX5 (Mk4) 2015+

Knowledge Base

Free to use workshop manual for your 2015+ Mk4 'ND' Mazda MX-5

< Previous Next >

DTC U2300:54 [BLIND SPOT MONITORING (BSM) CONTROL MODULE]

Description	Configuration data not received from instrument cluster
Detection condition	Blind spot monitoring (BSM) control module (LH) cannot receive the configuration data from the instrument cluster with the ignition switched ON (engine off or on).
Fail-safe	Blind spot monitoring (BSM) system is stopped.
Possible cause	NOTE: To correctly write the configuration data sent from the instrument cluster to the blind spot monitoring (BSM) control module (LH) to the blind spot monitoring (BSM) control module (LH), 30 s or more need to have elapsed since the ignition was switched ON (engine off or on). DTCs are stored in the instrument cluster. Instrument cluster configuration not implemented Instrument cluster internal memory malfunction Blind spot monitoring (BSM) control module (LH) malfunction
System wiring diagram	Not applicable

Diagnostic Procedure

Step	Inspection		Action
1	VERIFY INSTRUMENT CLUSTER DTCs Retrieve the instrument cluster DTCs using the M-MDS. (See DTC INSPECTION [INSTRUMENT CLUSTER].) Are any DTCs displayed?	Yes	Repair or replace the malfunctioning part according to the applicable DTC troubleshooting. (See DTC TABLE [INSTRUMENT CLUSTER].)
		No	Go to the next step.
2	RESET INSTRUMENT CLUSTER CONFIGURATION DATA Using the M-MDS, perform the instrument cluster configuration (using As-Built data). (See INSTRUMENT CLUSTER CONFIGURATION (USING AS-BUILT DATA).) Clear the DTC for the blind spot monitoring (BSM) control module using the M-MDS. (See CLEARING DTC [BLIND SPOT MONITORING (BSM) CONTROL MODULE].) Switch the ignition ON (engine off or on) and wait for 31.5 s or more. Retrieve the blind spot monitoring (BSM) control module DTCs using the M-MDS. (See DTC INSPECTION [BLIND SPOT MONITORING (BSM) CONTROL MODULE].) Is the same DTC displayed?	Yes	Using the M-MDS, perform the instrument cluster configuration (using As-Built data) again, then go to the next step. (See INSTRUMENT CLUSTER CONFIGURATION (USING AS-BUILT DATA).)
		No	Go to Step 4.
3	VERIFY THAT REPAIRS HAVE BEEN COMPLETED Clear the DTC for the blind spot monitoring (BSM) control module using the M-MDS. (See CLEARING DTC [BLIND SPOT MONITORING (BSM) CONTROL MODULE].) Switch the ignition ON (engine off or on) and wait for 31.5 s or more. Retrieve the blind spot monitoring (BSM) control module DTCs using the M-MDS. (See DTC INSPECTION [BLIND SPOT MONITORING (BSM) CONTROL MODULE].) Is the same DTC displayed?	Yes	Replace the blind spot monitoring (BSM) control module (LH), then go to the next step. (See BLIND SPOT MONITORING (BSM) CONTROL MODULE REMOVAL/INSTALLATION.)
		No	Go to the next step.
4	VERIFY IF OTHER DTCs DISPLAYED Are any other DTCs displayed?	Yes	Repair or replace the malfunctioning part according to the applicable DTC troubleshooting. (See DTC TABLE [BLIND SPOT MONITORING (BSM) CONTROL MODULE].)
		No	DTC troubleshooting completed.

< Previous Next >

This fan site is not affiliated with Mazda, and is intended for personal, or commercial use only. The content of our web pages is for general information purposes only and is presented “as is”. We give no assurance or warranty regarding the accuracy of the contents. Readers should do their due diligence and seek the advice of an appropriately certified automotive technician before attempting any steps on this site. Original content provided by Mazda North America. The content of the manual is copyright under DMCA to: full.metal.resistor@gmail.com

We accept no responsibility for errors, inaccuracies, or omissions found on these pages. Additionally, we hereby exclude liability for any demands, claims, damages or losses of any kind with regard to any content or information provided on our web-site, including but not limited to incidental or consequential damages, direct or indirect loss, compensatory damages, loss of profits, or otherwise. By using this manual you assume full liablity for any procedures carried out on your vehicle, and are responsible for the vehicle remaining road legal and safe.